AR · 10 kW solid-state amplifier

AR 10000W1000A

More than 10 kW of Class A solid-state power from 80 MHz to 1000 MHz, for whole-vehicle and military radiated immunity.

Request a quotation Spec sheet at ar.ametek-cts.com
AR 10000W1000A 10 kW solid-state amplifier
Key facts

AR 10000W1000A at a glance

  • Over 10 000 W CW nominal, 9500 W minimum at the 1 dB compression point, 80 MHz to 1000 MHz
  • Class A operation, completely solid state, push-pull output stages
  • 100 % mismatch tolerant
  • Touch screen digital control panel showing forward and reflected power
  • Forward and reflected RF sample ports, gain control and automatic level control
  • Scalable modular construction, housed in equipment racks
  • Remote control by Ethernet, USB, GPIB, fibre-optic serial and RS-232
  • Three-year manufacturer's warranty
  • US export classification EAR99

Figures from the manufacturer's product page. Specifications are subject to change; the datasheet governs. Quotations on request.

Where it fits

What the 10000W1000A is used for

The top of the W series is built for the largest test set-ups: whole-vehicle immunity to ISO 11451-2, MIL-STD-461 RS103 on platforms and large equipment, and RTCA/DO-160 Section 20 at the higher categories. It is one amplifier across the band, so there is no band switching below 1 GHz.

Which model a programme needs is a system design question, and at this power level the mains supply, cooling air and RF cabling are part of it. Send us your test plan and we will size the amplifier with the rest of the system.

Typical standards for this product

MIL-STD-461 RS103ISO 11452-2ISO 11451-2RTCA/DO-160 Section 20IEC 61000-4-3
Calibration

Calibrated on site, by the people who supplied it

Amplifiers, including AR models, are covered by our RF component calibration. High-power amplifiers are calibrated in the system, with the coupler and power sensor of the same path at the same visit. Calibration is carried out in your laboratory by the LAB Support Southeast Asia team, under the A2LA accredited ISO/IEC 17025 scope of LAB Support Ltd.

Amplifier and RF component calibration →
Related

Goes with the 10000W1000A

AR 10000A225D, 10 kHz to 225 MHz →AR 2000S1G2z8, 1 to 2.8 GHz →AR ATR26M6G-1 antenna →Frankonia EMC chambers →All AR models →
Frequently asked

AR 10000W1000A in Malaysia

Is the AR 10000W1000A solid state?

Yes, completely. It is a Class A solid-state amplifier with push-pull output stages, delivering over 10 kW from 80 MHz to 1000 MHz with no tubes.

Where can I buy the AR 10000W1000A in Malaysia?

ICX Lab Services in Penang is the authorised distributor of AMETEK CTS products, and AR is one of the brands under AMETEK CTS, together with EM TEST and Teseq. Send us the model number through the contact page or WhatsApp and we reply with a configuration and a quotation. Quotations on request.

Who installs and supports the 10000W1000A after delivery?

We do. ICX Lab handles delivery, installation and training, and coordinates factory service, firmware and repairs with AMETEK CTS on your behalf.

AR RF/Microwave Instrumentation is part of AMETEK Compliance Test Solutions. Product name, specifications and image are taken from ar.ametek-cts.com.

Need a quotation for the 10000W1000A?

Tell us the standards you test to and we will configure it with the accessories it needs.

Request a quotation   All AR models

Tell us what you need to test

We reply within one working day with a quote or a plan.

Contact us